CC Blog • Quick Bits • Resources

Gyrators

Written by Andrew Levido

A gyrator is a circuit that converts a capacitor into an inductor. There are a couple of reasons why we might want to do this – first because inductors are generally more expensive that other passive components, especially if you want close tolerances or high values. The second reason is that it is much easier to tune a gyrator circuit than an inductor.

We can start understanding at gyrators by looking at the negative impedance converter circuit shown in Figure 1. The analysis of this is pretty simple: the voltage at the output of the op amp must be 2 vin since the voltage at the op amp’s inverting input will be equal to that at its non-inverting input.

Figure 1
The input impedance of the negative impedance converter (NIC) is –Z. If the element Z is replaced by a capacitor, the input impedance is j/⍵C. The current lags the voltage like an inductor, but the impedance decreases with frequency like a capacitor.

We can then see that the current flowing through the impedance Z (and therefore iin flowing into the input terminal) must be –vin / Z, since it sees 2vin  on one end and vin on the other. The impedance seen looking into the input terminal is vin / iin  which is equal to –Z.

If the element Z were a capacitor with complex impedance –j/⍵C, the impedance looking into the negative impedance converter would be j/⍵C which is a kind of “backward” inductor. It is inductive in the sense that the current lags the voltage, but it has the wrong frequency characteristic – the impedance goes down with frequency instead of up!

If we put two negative impedance converters together as shown in Figure 2 it is easy enough to calculate the input impedance Zin = –R + (–R ∥ (R + Z)),  to be –R2/Z. Now if we set Z to be a capacitor with impedance –j/⍵C, the circuit  input impedance will be –j⍵CR2. This has both the phase lag and the right frequency dependence. We have created and inductor out of a capacitor.

Figure 2
If two negative impedance converters are used as shown here, the input impedance is –R2/Z. Now if the element Z is replaced by a capacitor the input impedance is j⍵CR2 which behaves like an inductor in both phase shift and frequency response.

Figure 3 shows one circuit, known as a generalised impedance converter (GIC), that can be used to implement this. The input impedance of this circuit is Zin = (Z1·Z3·Z5)/(Z2·Z4).  If Z4 is a capacitor and the rest are resistors, for example, the circuit behaves like an inductor with value L = (R1·R3·R5·C4)/R2.

The circuit is called a general impedance converter because you can do other things with it. If you put capacitors at Z3 and Z5 (and resistors everywhere else) you get a frequency dependent negative resistor!

There is one obvious limitation of the GIC implementation of the gyrator – you can only emulate a ground-connected inductor. You can’t use this circuit to implement a floating inductor. There is a circuit that can do this, called the Riordan gyrator, but it is relatively complex.

Another limitation of the gyrator is the op amp’s bandwidth. The GIC circuit shown in Figure 3 will stop looking like an inductor at something like a 100th of the op amp’s bandwidth. For example, a GIC implemented with op amps with a GBW of 5MHz will be good only to about 50kHz. Above this there will be a resonance, then the circuit will look capacitive.

Figure 3
The generalised impedance converter (GIC) shown here can be used to implement a gyrator. If Z4 is a capacitor and the rest are resistors the resulting circuit looks like an inductor with a value of (R1·R3·R5·C4)/R2.

The gyrator circuit is nonetheless very useful since you can vary the inductance by changing one of the resistor values. For example, a lot of analog graphic equalisers use this technique.  You can create high-value inductors with very high Q factors (1000 is readily achievable at up to around 1H) something very difficult to achieve with real inductors.

Bibliography

“Frequency-Dependent Negative Resistor.” In Wikipedia, February 3, 2024. https://en.wikipedia.org/w/index.php?title=Frequency-dependent_negative_resistor&oldid=1202723552.

“Negative Impedance Converter.” In Wikipedia, April 22, 2023. https://en.wikipedia.org/w/index.php?title=Negative_impedance_converter&oldid=1151188797.

ResearchGate. “Figure 1. The Application Circuits of Two Types Riordan Simulated…” Accessed August 25, 2024. https://www.researchgate.net/figure/The-application-circuits-of-two-types-Riordan-simulated-inductors-a-the-Riordan_fig1_333468307.

Horowitz, Paul, and Winfield Hill. The Art of Electronics. Third edition, 11th printing, with Corrections. Cambridge New York, NY: Cambridge University Press, 2017.

Keep up-to-date with our FREE Weekly Newsletter!

Don't miss out on upcoming issues of Circuit Cellar.


Note: We’ve made the Dec 2022 issue of Circuit Cellar available as a free sample issue. In it, you’ll find a rich variety of the kinds of articles and information that exemplify a typical issue of the current magazine.

Would you like to write for Circuit Cellar? We are always accepting articles/posts from the technical community. Get in touch with us and let's discuss your ideas.

Sponsor this Article
+ posts

Andrew Levido (andrew.levido@gmail.com) earned a bachelor’s degree in Electrical Engineering in Sydney, Australia, in 1986. He worked for several years in R&D for power electronics and telecommunication companies before moving into management roles. Andrew has maintained a hands-on interest in electronics, particularly embedded systems, power electronics, and control theory in his free time. Over the years he has written a number of articles for various electronics publications and occasionally provides consulting services as time allows.

Supporting Companies

Upcoming Events


Copyright © KCK Media Corp.
All Rights Reserved

Copyright © 2026 KCK Media Corp.

Gyrators

by Andrew Levido time to read: 3 min