I/O Raspberry Pi Expansion Card

The RIO is an I/O expansion card intended for use with the Raspberry Pi SBC. The card stacks on top of a Raspberry Pi to create a powerful embedded control and navigation computer in a small 20-mm × 65-mm × 85-mm footprint. The RIO is well suited for applications requiring real-world interfacing, such as robotics, industrial and home automation, and data acquisition and control.

RoboteqThe RIO adds 13 inputs that can be configured as digital inputs, 0-to-5-V analog inputs with 12-bit resolution, or pulse inputs capable of pulse width, duty cycle, or frequency capture. Eight digital outputs are provided to drive loads up to 1 A each at up to 24 V.
The RIO includes a 32-bit ARM Cortex M4 microcontroller that processes and buffers the I/O and creates a seamless communication with the Raspberry Pi. The RIO processor can be user-programmed with a simple BASIC-like programming language, enabling it to perform logic, conditioning, and other I/O processing in real time. On the Linux side, RIO comes with drivers and a function library to quickly configure and access the I/O and to exchange data with the Raspberry Pi.

The RIO features several communication interfaces, including an RS-232 serial port to connect to standard serial devices, a TTL serial port to connect to Arduino and other microcontrollers that aren’t equipped with a RS-232 transceiver, and a CAN bus interface.
The RIO is available in two versions. The RIO-BASIC costs $85 and the RIO-AHRS costs $175.

Roboteq, Inc.
www.roboteq.com

Linear Regulator with Current and Temperature Monitor Outputs

Linear Technology Corp

Linear Technology Corp

The LT3081 is a rugged 1.5-A wide input voltage range linear regulator with key usability, monitoring, and protection features. The device has an extended safe operating area (SOA) compared to existing regulators, making it well suited for high input-to-output voltage and high output current applications where older regulators limit the output.

The LT3081 uses a current source reference for single-resistor output voltage settings and output adjustability down to ”0.” A single resistor can be used to set the output current limit. This regulator architecture, combined with low-millivolt regulation, enables multiple ICs to be easily paralleled for heat spreading and higher output current. The current from the device’s current monitor can be summed with the set current for line-drop compensation, where the LT3081’s output increases with current to compensate for line drops.

The LT3081 achieves line and load regulation below 2 mV independent of output voltage and features a 1.2-to-40-V input voltage range. The device is well suited for applications requiring multiple rails. The output voltage is programmable with a single resistor from 0 to 38.5 V with a 1.2-V dropout. The on-chip trimmed 50-µA current reference is ±1% accurate. The regulation, transient response, and output noise (30 µVRMS) are independent of output voltage due to the device’s voltage follower architecture.

Two resistors are used to configure the LT3081 as a two-terminal current source. Input or output capacitors for stability are optional in either linear regulator or current-source operation mode. The LT3081 provides several monitoring and protection functions. A single resistor is used to program the current limit, which is accurate to ±10%. Monitor outputs provide a current output proportional to temperature (1 µA/°C) and output current (200 µA/A), enabling easy ground-based measurement. The current monitor can compensate for cable drops. The LT3081’s internal protection circuitry includes reverse-input protection, reverse-current protection, internal current limiting, and thermal shutdown.

A variety of grades/temperature ranges are offered including: the E and  I grades (–40°C to 125°C), the H grade (–40°C to 150°C), and the high-reliability MP grade (–55°C to 50°C). Pricing for the E-grade starts at $2.60 each in 1,000-piece quantities.

Linear Technology Corp.
www.linear.com

Low-Power, High-Efficiency Boost Regulator

The TS3300 is an ultra-low-power, load-independent, high-efficiency boost regulator. It operates from supply voltages as low as 0.6 up to 4.5 V and can deliver at least 75 mA of continuous output current.

The TS3300 can be powered from a variety of power sources including single- or multiple-cell alkaline or single Li-chemistry batteries. The boost regulator’s output voltage range can be user-specified from 1.8 to 5.25 V to simultaneously power a range of low-power analog circuits, microcontrollers, and low-energy Bluetooth radios. The TS3300 produces a 3-V output from a 1.2-V input source. Its efficiency performance is constant over a 100:1 span in output current. To power low-energy radios, the TS3300’s internal, low-dropout linear regulator can deliver up to 100 mA output current while reducing boost-converter-generated output voltage ripple.

Drawing only 3.5 µA no-load supply current, the TS3300 is ideal for “always on” and other battery-powered or portable applications where an extended battery run-time is required. The TS3300 operates from low power sources (e.g., photovoltaic cells to three alkaline cells) and is ideally suited for handheld/portable applications (e.g., wireless remote sensors, RFID tags, wireless microphones, solar cell post-regulator/chargers, post-regulators for energy harvesting, blood glucose meters, and personal health-monitoring devices).

The TS3300 is fully specified over the –40°C-to-85°C temperature range and is available in a low-profile, thermally-enhanced 16-pin 3mm × 3mm TQFN package with an exposed backside paddle. The TS3300 costs $0.85 in 1,000-unit quantities.

Touchstone Semiconductor
http://touchstonesemi.com