Shlomo Engelberg, an associate professor in the electronics department of the Jerusalem College of Technology, is well-versed in signal processing. As an instructor and the author of several books, including Digital Signal Processing: An Experimental Approach (Springer, 2008), he is a skilled guide to how to use the UART “protocol” to implement systems that transmit and receive data without a built-in peripheral.
Implementing serial communications using software rather than hardware is called bit-banging, the topic of his article in Circuit Cellar’s June issue.
“There is no better way to understand a protocol than to implement it yourself from scratch,” Engelberg says. “If you write code similar to what I describe in this article, you’ll have a good understanding of how signals are transmitted and received by a UART. Additionally, sometimes relatively powerful microprocessors do not have a built-in UART, and knowing how to implement one in software can save you from needing to add an external UART to your system. It can also reduce your parts count.”
In the excerpt below, he explains some UART fundamentals:
WHAT DOES “UART” MEAN?
UART stands for universal asynchronous receiver/transmitter. The last three words in the acronym are easy enough to understand. “Asynchronous” means that the transmitter and the receiver run on their own clocks. There is no need to run a wire between the transmitter and the receiver to enable them to “share” a clock (as required by certain other protocols). The receiver/transmitter part of the acronym means just what it says: the protocol tells you what signals you need to send from the transmitter and what signals you should expect to acquire at the receiver.
The first term of the acronym, “universal,” is a bit more puzzling. According to Wikipedia, the term “universal” refers to the fact that the data format and the speed of transmission are variable. My feeling has always been that the term “universal” is basically hype; someone probably figured a “universal asynchronous receiver/transmitter” would sell better than a simple “asynchronous receiver/transmitter.”
Before you can use a UART to transfer information from device to device, the transmitter and receiver have to agree on a few things. First, they must agree on a transmission speed. They must agree that each transmitted bit will have a certain (fixed) duration, denoted TBIT. A 1/9,600-s duration is a typical choice, related to a commonly used crystal’s clock speed, but there are many other possibilities. Additionally, the transmitter and receiver have to agree about the number of data bits to be transmitted each time, the number of stop bits to be used, and the flow control (if any).
When I speak of the transmitter and receiver “agreeing” about these points, I mean that the people programming the transmitting and receiving systems must agree to use a certain data rate, for example. There is no “chicken and egg” problem here. You do not need to have an operational UART before you can use your UART; you only need a bit of teamwork.
Using a UART is considered the simplest way of transmitting information. Figure 1 shows the form the transmissions must always make. The line along which the signal is transmitted is initially “high.” The transmissions begin with a single start bit during which the line is pulled low (as all UART transmissions must). They have eight data bits (neither more nor less) and a single stop bit (and not one and a half or two stop bits) during which the line is once again held high. (Flow control is not used throughout this article.)
Why must this protocol include start and stop bits? The transmitter and the receiver do not share a common clock, so how does the receiver know when a transmission has begun? It knows by realizing that the wire connecting them is held high while a transmission is not taking place, “watching” the wire connecting them, and waiting for the voltage level to transition from high to low, which it does by watching and waiting for a start bit. When the wire leaves its “rest state” and goes low, the receiver knows that a transmission has begun. The stop bit guarantees that the line returns to its “high” level at the end of each transmission.
Transmissions have a start and a stop bit, so the UART knows how to read the two words even if one transmits that data word 11111111 and follows it with 11111111. Because of the start and stop bits, when the UART is “looking at” a line on which a transmission is beginning, it sees an initial low level (the start bit), the high level repeated eight times, a ninth high level (the stop bit), and then the pattern repeats. The start bit’s presence enables the UART to determine what’s happening. If the data word being transmitted were 00000000 followed by 00000000, then the stop bit would save the day.
The type of UART connection I describe in this article only requires three wires. One wire is for transmission, one is for reception, and one connects the two systems’ grounds.
The receiver and transmitter both know that each bit in the transmission takes TBIT seconds. After seeing a voltage drop on the line, the receiver waits for TBIT/2 s and re-examines the line. If it is still low, the receiver assumes it is in the middle of the start bit. It waits TBIT seconds and resamples the line. The value it sees is then used to determine data bit 0’s value. The receiver then samples every TBIT seconds until it has sampled all the data bits and the stop bit.
Engelberg’s full article, which you can find in Circuit Cellar’s June issue, goes on to explain UART connections and how he implemented a simple transmitter and receiver. For the projects outlined in his article, he used the evaluation kit for Analog Devices’s ADuC841.
“The transmitter and the receiver are both fairly simple to write. I enjoyed writing them,” Engelberg says in wrapping up his article. “If you like playing with microprocessors and understanding the protocols with which they work, you will probably enjoy writing a transmitter and receiver too. If you do not have time to write the code yourself but you’d like to examine it, feel free to e-mail me at email@example.com. I’ll be happy to e-mail the code to you.”