New Products: May 2013

iC-Haus

iC-Haus iC-TW8

The iC-TW8 is a high-resolution signal processor designed to evaluate sine/cosine sensors. Its automatic functions help minimize angular errors and jitters. The processor can be used for initial, push-button calibration and to permanently adapt signal-path parameters during operation. The angular position is calculated at a programmable resolution of up to 65,536 increments per input cycle and output as an indexed incremental signal. A 32-bit word, which includes the counted cycles, is available through the SPI.

As an application-specific DSP, the iC-TW8 has two ADCs that simultaneously sample at a 250-ksps rate, fast CORDIC algorithms, special signal filters, and an analog front end with differential programmable gate amplifier (PGA) inputs that accepts typical magnetic sensor signals from 20 mVPP and up. Signal frequencies of up to 125 kHz enable high rotary and linear speeds for position measuring devices and are processed at a 24-µs constant latency period.

The device’s 12-bit measurement accuracy works with one button press. Measuring tools are not required. The iC-TW8 independently acquires information about the signal corrections needed for offset, amplitude, and phase errors and stores them in an external EEPROM.

The iC-TW8 has two configuration modes. Preset functions and interpolation factors can be retrieved through pins and the device can be calibrated with a button push. No programming is required for initial operation.

The device’s functions—including an AB output divider for fractional interpolation, an advanced signal filter to reduce jitter, a table to compensate for signal distortion, and configurable monitors for errors and signal quality—can be accessed when the serial interfaces are used. Typical applications include magnetic linear displacement measuring systems, optical linear scales, programmable magnetic/optical incremental encoders, high-resolution absolute/incremental angle sensors with on-axis, Hall scanning, and the general evaluation of sine/cosine signals (e.g., PC measuring cards for 1 VPP and 11 µAPP).

The iC-TW8 operates on a 3.1-to-5.5-V single-ended supply within a –40°C-to-125°C extended operating temperature range. It comes in a 48-pin QFN package that requires 7 mm × 7 mm of board space. A ready-to-operate demo board is  available for evaluation. An optional PC operating program, in other words, a GUI, can be connected with a USB adapter.

The iC-TW8 costs $7.69 in 1,000-unit quantities.

iC-Haus GmbH

www.ichaus.com


ULTRASOUND RECEIVERS

Analog Devices AD9675

The AD9675 and the AD9674 are the latest additions to Analog Devices’s octal ultrasound receiver portfolio. The devices and are pin compatible with the AD9670/AD9671.

The AD9675 is an eight-channel ultrasound analog front end (AFE) with an on-chip radio frequency (RF) decimator and Analog Devices’s JESD204B serial interface. It is designed for mid- to high-end portable and cart-based medical and industrial ultrasound systems. The device integrates eight channels of a low-noise amplifier, a variable-gain amplifier, an anti-aliasing filter, and a 14-bit ADC with a 125-MSPS sample rate and a 75-dB signal-to-noise ratio (SNR) performance for enhanced ultrasound image quality. The on-chip RF decimator enables the ADC to be oversampled, providing increased SNR for improved image quality while maintaining lower data I/O rates. The 5-Gbps JESD204B serial interface reduces ultrasound system I/O data routing.

The AD9674 offers similar functionality, but includes a standard low-voltage differential signaling (LVDS) interface. Both devices are available in a 144-ball, 10-mm × 10-mm ball grid array (BGA) package.

The AD9674 and the AD9675 cost $62 and $68, respectively.

Analog Devices, Inc.

www.analog.com


LOW-VOLTAGE DIGITAL OUTPUT HALL-EFFECT SENSORS

Melexis MLX92212

Melexis MLX92212

MLX92212 digital output Hall-effect sensors are AEC-Q100-qualified devices that deliver robust, automotive-level performance. The MLX92212LSE-AAA low-hysteresis bipolar latch and the MLX92212LSE-ABA high-hysteresis unipolar switch are optimized for 2.5-to-5.5-V operation. They pair well with many low-power microcontrollers in embedded systems. The sensor and specified microcontroller can share the same power rail. The sensors’ open-drain outputs enable simple connectivity with CMOS/TTL. They exhibit minimal magnetic switch point drift over temperature (up to 150°C) or lifetime and can withstand 8 kV electrostatic discharge.

The MLX92212LSE-AAA is designed for use with multipole ring magnets or alternating magnetic fields. It is well suited for brushless DC electric motor commutation, speed sensing, and magnetic encoder applications. Typical automotive uses include anti-trap/anti-pinch window lift controls, automatic door/hatch systems, and automatic power seat positioning. The MLX92212LSE-ABA enables the use of generic/weak magnets or larger air gaps. It can be used in simple magnetic proximity sensing and interlocks in covers/hatches or ferrous-vane interrupt sensors for precise position and timing applications.

Both MLX92212 devices utilize chopper-stabilized amplifiers with switched capacitors. The CMOS technology makes this technique possible and contributes to the sensors’ low current consumption and small chip size.

The MLX92212 sensors cost $0.35 each in 5,000-unit quantities and $0.30 in 10,000-unit quantities.

Melexis Microelectronic Integrated Systems

www.melexis.com


POWERFUL SPI ADAPTERS

Byte SPI Storm

Byte SPI Storm

The SPI Storm 50 and the SPI Storm 10 are the latest versions of Byte Paradigm’s SPI Storm serial protocol host adapter. The adapters support serial peripheral interface (SPI), Quad-SPI, and custom serial protocols in the same USB device.

The SPI Storm 50 and the SPI Storm 10 support serial protocols and master up to 50 and 10 MHz, respectively. The SPI Storm 10 features an 8-MB memory, while the higher-end devices are equipped with a 32-MB memory.

The SPI Storm adapters enable system engineers to access, communicate, and program their digital board and digital ICs, such as field-programmable gate array (FPGA), flash memories, application-specific integrated circuit (ASIC), and

system-on-a-chip (SoC). The SPI Storm 10 is well suited for engineering schools and universities because it is a flexible, all-around access device for hands-on digital electronics. The 50- and 100-MHz versions can be used in mid- and high-end testing and debugging for telecommunications, medical electronics, and digital imaging industries.

The SPI Storm 50 and the SPI Storm 10 cost $530 and $400, respectively.

Byte Paradigm

www.byteparadigm.com


ANALOG-BASED POWER MANAGEMENT CONTROLLER WITH INTEGRATED MCU

Microchip MCP19111

Microchip MCP19111

The MCP19111 digitally enhanced power analog controller is a new hybrid, digital and analog power-management device. In combination with the expanded MCP87xxx family of low-figure-of-merit (FOM) MOSFETs, it supports configurable, high-efficiency DC/DC power-conversion designs for many consumer and industrial applications.

The MCP19111 controller, which operates at 4.5 to 32 V, integrates an analog-based PWM controller with a fully functional flash-based microcontroller. This integration offers the flexibility of a digital solution with the speed, performance, and resolution of an analog-based controller.

The MCP19111 devices have integrated MOSFET drivers configured for synchronous, step-down applications. The MCP87018, MCP87030, MCP87090, and MCP87130 are 25-V-rated, 1.8-, 3-, 9-, and 13-mΩ logic-level MOSFETs that are specifically optimized for switched-mode-power-supply (SMPS) applications.

The MCP19111 evaluation board includes Microchip’s high-speed MOSFETs. This evaluation board includes standard firmware, which is user-configurable through an MPLAB X IDE graphical user interface (GUI) plug-in. The combined evaluation board, GUI, and firmware enable power-supply designers to configure and evaluate the MCP19111’s performance for their target applications.

The MCP19111 controllers cost $2.81 each and the MCP87018/030/090/130 MOSFETs cost $0.28 each, all in 5,000-unit quantities.

Microchip Technology, Inc.

www.microchip.com


ELASTOMER SOCKET FOR HIGH-SPEED QFP ICs

Ironwood SG-QFE-7011

Ironwood SG-QFE-7011

The SG-QFE-7011 is a high-performance QFP socket for 0.4-mm pitch, 128-pin QFPs. The socket is designed for a

1.6-mm × 14-mm × 14-mm package size with a 16-mm × 16-mm lead tip to tip. It operates at bandwidths up to 10 GHz with less than 1 dB of insertion loss and has a typical 20 mΩ per I/O contact resistance. The socket connects all pins with 10-GHz bandwidth on all connections. The small-footprint socket is mounted with supplied hardware on the target PCB. No soldering is required. The small footprint enables inductors, resistors, and decoupling capacitors to be placed close to the device for impedance tuning.

The SG-QFE-7011’s swivel lid has a compression screw that enables ICs to be quickly changed out. The socket features a floating compression plate to force down the QFP leads on to elastomer. A hard-stop feature is built into the compression mechanism.

The sockets are constructed with high-performance, low-inductance gold-plated embedded wire on elastomer as interconnect material between a device and a PCB. They feature a –35°C-to-100°C temperature range, a 0.15-nH pin self inductance, a 0.025-nH mutual inductance, a 0.01-pF capacitance to ground, and a 2-A per pin current capacity.

The SG-QFE-7011 costs $474.

Ironwood Electronics

www.ironwoodelectronics.com

Leave a Reply

Your email address will not be published. Required fields are marked *

CAPTCHA Image

*

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>